TEC 1720-G

TEC 1720-G
Be the first to write a review.


Aerosols and Cleaners, Chemicals, Products Made in the U.S.A., Techspray, Techspray ESD Products

Techspray 1720-G Zero Charge Floor Coating 1 gal Jug

Part #: TEC 1720-G
MSRP: $77.76 GAL
Price: $69.86 GAL
Minimum Order Qty: 1
Must be Purchased in Multiples of: 1
Leadtime: Inventory Listed Below - Otherwise Usually Ships In 10-14 Days

Stock Availability

MAIN - NJ 08805 0 GAL

The Techspray 1720-G is a Zero Charge, ESD Safe Floor Coating. This coating is fast drying and anti-static that eliminates static charge and reduces triboelectric generation from flexible surfaces. It is ideal for plastics, fabrics, and carpet. This item comes in a 1 gal jug.
Techspray's ESD-safe products can help maintain work areas within the ANSI/ESDS20.20 standards set by the ESD Association (www.esda.com). In a static-free environment, the work area, tools and personnel form a circuit. Electrostatic Discharge (ESD) occurs when the charges of two surfaces with a large electronic potential (difference) equalize instantaneously. The resulting discharge or spark can cause catastrophic or latent damage to electronic components. ESD programs maintain an equal potential by maintaining continuous contact with ground, avoiding ESD damage. Cleaners, lotions, and coatins are an integral part of an ESD control program.
Instructions: With a new mop and clean pails, apply coating as follows: 1. Apply thin coat to floor, i.e 3/4 way down on the ringer. Let dry to touch, approximately 45-60 minutes. 2. Apply a second coat, approximately 1/2 way down on the ringer. Note: Two coats only are recommended for conductive tile. 3. If a third coat is applied, wait 24-hour waiting period/dry time after previous coat. If a third coat is applied, the floor space may be occupied once it is dry. After that a 6-hour wait, buff the floor with a coating yield of 1,200 ft2 for each gallon of coating per coat.
Chemical amp; Physical Properties:
Appearance: Opaque white
Odor: Aromatic odor
Flash Point: none
VOC (EPA) 5.15 percent wt, 53.73 g/l
Boiling Point: 100 Degrees C (212 Degrees F)
Density: 1.04 at 25 Degrees C
Chemical Composition (Chemical Name / CAS ):
Water / 7732-18-5
Acrylate Copolymer
Ethanol,2-butoxy-,phosphate / 78-51-3
1,2-Propanediol / 57-55-6
Potassium Chloride / 7447-40-7
Alcohols, C12-C13, ethoxylated / 66455-14-9
Ethoxylated secondary alcohol / 84133-50-6
Sodium lauryl sulfate / 68585-47-7
Sodium laurel ether sulfate / 68891-38-3
Tall oil fatty acid potassium salt / 61790-44-1
5-Chloro-2-methyl-3(2H)-isothiaxolone,mixt. with 2-methyl-3(2H)- / 55965-84-9

1 gal jug
Resistivity between 10^6 To 10^10
High gloss polymer
Non-ozone depleting
Slip resistant
Effective in low humidity
Zinc free

Prices subject to change without notice. Stock can change at any time. Prices are for online orders only. Stock items typically ship in 24-48 hours. Special orders with the manufacturer vary and are subject to their leadtimes.

WBENC Certified  Visa Mastercard Discover AMEX  Paypal Buyer Credit Click for the BBB Business Review of this Soldering Equipment in Bound Brook NJ  Official PayPal Seal    McAfee Secured