Techspray 1654-5G Precision-V Vapor-Degreaser Parts Cleaner 50 lb Pail

The Techspray 1654-5G is a Precision-V Vapor-Degreaser Parts Cleaner. This item is a 50 lb large drum. This item is the ideal replacement for AK225-based cleaners, which will be phased out by 2015 due to ozone depletion restrictions. (See side bar at left) Azeotropic properties that allow it to maintain stable as it is cycled in a vapor-degreaser. It is not reactive nor corrosive to metals commonly found in the construction of vapor-degreasers. Exposure to Precision-V solvents is less hazardous than many other solvents commonly used in vapor-degreasers: e.g. TCE, nPB, and Perc. Precision-V solvents have a lower boiling point than most other vapor-degreaser solvents. This reduces heat-stress on components being cleaned and reduces energy consumption from the boil sump and chiller coils. Prevision-V Parts Cleaner removes oils, greases, silicones and other common industrial contaminants. Instructions:Reclamation Process: The reclamation (i.e. boil down) process utilizes the vapor-degreaser as a still to distill solvent from the dirty boil sump and allows you to reclaim and reuse this solvent. When it is determined that the Boil Sump needs to be cleaned out, you should do the following things to boil down the solvent: 1. If you have a 2 sump vapor-degreaser, drain the rinse sump into a clean container for reuse. If you have a one-sump vapor-degreaser, drain the spray reservoir using the spray wand. This material should be collected in a clean container, so it can be reused. 2. Allow the solvent to continue to boil, and the vapors to condense, until such time as one of two things happen: a. the High Temperature Control (HTC) trips and turns off the heat to the heating elements or b. the Liquid Level Control trips because the level in the Boil Sump is too low. 3. Drain the remaining solvent/soil mixture into a container that is labeled as Hazardous Waste. This material can be used in future boil downs to reclaim more of the solvent in the mixture. 4. Use the retained solvent (from step 1) to refill the vapor-degreaser and add whatever volume of solvent is necessary to completely fill the machine. This process can be repeated as often as necessary, depending on the amount of usage of the vapor-degreaser and the amount of soil that is introduced into the vapor-degreaser. When you boil down, always put the solvent/soil mixture into the vapor-degreaser to reclaim additional amount of the solvent from this mixture. Chemical amp; Physical Properties:Appearance: Clear, colorless liquidOdor: Faint ethereal odorFlash Point: noneVOC (EPA): 42 percentBoiling Point: 34.4 Degrees C (94 Degrees F)Density: 1.3417 at 25 Degrees C Chemical Composition (Chemical Name / CAS NUMBER):1,1,1,2,2,3,4,5,5,5-decafluoropentane / 138495-42-81,2-transdichloroethylene / 156-60-51,1,1,3,3,-pentafluorobutane (HFC-365mfc) / 406-58-6Nitromethane / 75-52-5 Metals Compatibility (Material Name / Rating):Brass foil / Excellent short-term, slight reaction long-termCopper foil / Excellent short-term, slight reaction long-termNickel 200 / Excellent short-term, slight reaction long-termAluminum 6061 / ExcellentAluminum 2024 / Excellent short-term, slight reaction long-termStainless steel 316 / ExcellentStainless steel 304 / ExcellentMild carbon steel / Slight reaction short- and long-termGalvanized steel / Excellent
* 50 lb pail* Powerful cleaner* Non-flammable* Non-ozone depleting* Safe on electronics* Rapid evaporation* Zero residue* Safe on most plastics* EPA SNAP approved* Low VOC* Vapor-degreaser formula